User Manual
Release 1.0

Chipsee Products Naming Rules
CS10600RA070E-C111
CS10600RA070P-C111 |
|
CS | Chipsee Product Abbreviate |
10 | Horizontal Resolution
80 Means 800 Pixel 10 Means 1024 Pixel 12 Means 1280 Pixel 14 Means 1440 Pixel 19 Means 1920 Pixel |
600 | Vertical Resolution
480 Means 480 Pixel 600 Means 600 Pixel 768 Means 768 Pixel 800 Means 800 Pixel 900 Means 900 Pixel 102 Means 1024 Pixel 108 Means 1080 Pixel |
RA | Raspberry |
070 | LCD Dimension
050 Means 5.0 Inch 070 Means 7.0 Inch 080 Means 8.0 Inch 097 Means 9.7 Inch 101 Means 10.1 Inch 104 Means 10.4 Inch 120 Means 12.0 Inch 150 Means 15.0 Inch 170 Means 17.0 Inch 190 Means 19.0 Inch 215 Means 21.5 Inch |
E | Means Embedded PC or Panel PC
E Means Embedded PC without Case P Means Panel PC with Case |
C | Means Touch Type
R Means Resistive Touch C Means Capacitive Touch |
1 | Means LCD Brightness
1 Means Common Brightness 2 Means High Brightness |
2 | PCB Version
Baseboard PCB Version Number |
1 | PCB Version
SOM Module PCB Version Number |
Hardware Features
Key Features: | |
CPU | Raspberry Pi® CM3, CM3 Lite ;
Raspberry Pi® CM3+, CM3+ Lite; 1.2GHZ |
Storage | 2 TF card slotsOne TF Card slot design for Lite version that has no eMMC.The other one TF Card slot design for storage expansion |
Display | 7.0 Inch IPS LCD,1024*600 Pixel Resolution
High Brightness: 500nit |
Touch | Capacitive Touch (Five-Point) |
USB | 2 x USB 2.0 Host |
LAN | 1 Channel 100M LAN |
Audio | 3.5mm Audio Out Connector, 2W Speaker Internal |
Buzzer | 1 |
RTC | Yes, High Accuracy RTC with Lithium Button Coin battery |
RS232 | 2 Channels |
RS485 | 1 Channel ,The RS485 multiplex with the RS232_1.That means customer can’t use RS232_1 and the RS485 as the same time. |
GPIO | Opto-Isolated GPIO, 4Input,4 Output, Can drive up 500mA current every Channel at most (external power source) |
WiFi/BT | On Board WiFi/BT |
HDMI | 1 Channel |
SATA II | 1 Channel |
3G/4G | Yes, Not mount by default |
Camera | Yes, Not mount by default |
Power Input | 6~36V DC |
Current @ 12V | 700 mA max |
Power Consumption | 8.4W Typical |
Working Temperature | -20°C to +70°C |
OS | Debian |
Dimension | Without Metal Case: 190*107.8*27.7mm
With Metal Case: 206*135*30.1mm |
Weight | Without Metal Case: 400g
With Metal Case: 700g |
CS10600RA070E-C111

Figure 1 Top View (Debian)

Figure 2 Back View (Debian)
CS10600RA070P-C111

Figure 3 Top View (Debian)

Figure 4 Back View (Debian)
Power Input Connector
The product CS10600RA070E/CS10600RA070P uses a wide range power input: DC 6~36V. The total power consumption is normally about 6.6W. There are two types of power input interface.
The Power Input connector is a 3 Pin 3.81mm screw terminal connector, as can be seen on Figure 5. The “+” character stands for positive power input, the “-” character stands for negative power input. The “G” character stands for system Ground.
For more information take a look at Table 1 – it has detailed descriptions about the connector definition.
The other power input interface is the 2.1mm DC input head, as shown in Figure 6.

Figure 5 Power Input Connector
Table 1
Power Input Pin Definition: | ||
Pin Number | Definition | Description |
Pin 1 | Positive Input | Connect to DC Power Positive Terminal |
Pin 2 | Negative Input | Connect to DC Power Negative Terminal |
Pin 3 | Ground | Connect to Power System Ground |



Figure 6 Power Input Connector
ATTENTION:
The system ground “G” has been connected to power negative “-” on board.
CAN+RS485+RS232 Connector
The RS485+RS232 connector is a 8 Pin 3.81mm screw terminal connector, as seen in Figure 7. As for the definition of every pin, please refer to Table 2.
This product has 2 channels of UART in total.

Figure 7 RS485+RS232 Connector
Table 2
RS232 / RS485 Pin Definition: | ||
Pin Number | Definition | Description |
Pin 8 | RS485_1- | CPU UART1, RS485 –(B) signal |
Pin 7 | RS485_1+ | CPU UART1, RS485 +(A) signal |
Pin 6 | RS232_1_RXD | CPU UART1, RS232 RXD signal |
Pin 5 | RS232_1_TXD | CPU UART1, RS232 TXD signal |
Pin 4 | RS232_0_RXD | CPU UART0, RS232 RXD signal |
Pin 3 | RS232_0_TXD | CPU UART0, RS232 TXD signal |
Pin 2 | GND | System Ground |
Pin 1 | +5V | System +5V Power Output, No more than 1A Current output. |
ATTENTION:
RS485_1 and RS232_1 share the same channel UART1. You cannot use RS485_1 and RS232_1 at the same time.
GPIO Connector
This product CS10768RA070E/CS10768RA070P has a GPIO interface, as shown in Figure 8. For the interface definition refer to table 3.

Figure 8 GPIO Connector
Capacitive Touch
The product CS10600RA070E/CS10600RA070P uses a Single Point capacitive touch, as seen in Figure 9.

Figure 9 Capacitive Touch Connector
USB HOST Connector
As can be seen in Figure 10, the product CS10600RA070E/CS10600RA070P has two USB2.0 connectors.


Figure 10 USB HOST Connector
LAN Connector
The product CS10600RA070E/CS10600RA070P has one channel 100Mbit Ethernet connector, as Figure 11 shows.


Figure 11 LAN Connector
Audio Connector
The product has one audio output, as shown in Figure 12. It also has an internal 2W speaker.


Figure 12 Audio Connector
TF Card
The product CS10600RA070E/CS10600RA070P has two TF (uSD) card connectors, as shown in Figure 13. It supports TF (uSD) cards up to 32GB.


Figure 13 TF Card Connector
ATTENTION:
The TF card slot is NOT mounted with any TF card by default.
Mini USB
The product CS10600RA070E/CS10600RA070P has one Mini USB port which is used for downloading the system to the eMMC of CM3/CM3+.



Figure 14 Mini USB Connector
Start switch
The start switch turns the product on or off. The toggle switch can change the startup sequence. You can choose a start position with SD or eMMC. This switch is labeled SW1 on the PCB, as shown in Figure 15.

Figure 15 Boot Switch
SIM Card Holder
The product CS10768RA070E/CS10768RA070P has a mini-PCIe connector inside. The customer can mount on a 4G module to it.
If the customer chooses to add the 4G module, they will need the SIM card holder, as shown in Figure 17. There is a connector on the backside of the case which can connect an external 4G Antenna, as shown in Figure 18.

Figure 16 mini-PCIe Connector&4G Module

Figure 17 SIM Card

Figure 18 4g antenna
ATTENTION:
This product is not mounted on with any 4G module by default.
WiFi+BT
The product CS10600RA070E/CS10600RA070P has one WiFi+BT. It uses the Realtech RTL8723, which integrates WiFi and BT, as shown in Figure 19. For CS10600RA070P, there is a connector on the backside of the case which can connect an external WiFi/BT antenna, as shown in Figure 20.

Figure 19 WiFi+BT Module

Figure 20 WiFi+BT Antenna
Measurements and Mounting
Measurements of CS10600RA070E
The measurement of CS10600RA070E -C111 is 190*107.8*27.7mm, as Figure 21 shows.
Mounting of CS10600RA070E
The product CS10600RA070E can be mounted using the 4 screw holes on the PCB as shown in Figure 14. Please make sure the display is not exposed to high pressure when mounting into an enclosure.

Figure 21 Dimension
Measurements of CS10600RA070P
The measurement of CS10600RA070P -C111 is 206*135*30.1mm.
Mounting of CS10600RA070P
This product CS10600RA070P can be mounted using the mounting set, as Figure 22 shows. Please make sure the display is not exposed to high pressure when mounting into an enclosure.



Figure 22 Mounting Method
Raspbian Buster on the Industrial Pi
Images of the Raspbian Buster operating system on the Industrial Pi.
How to Get Support
Please feel free to contact us with any questions, queries or suggestions.
If your question is about technical support or troubleshooting for one of our products, we kindly ask you to first check our documentation for a possible solution.
If you cannot find the solution you are looking for then please write to service@chipsee.cn providing all possible details.