User Manual
Release 1.0


Chipsee Products Naming Rules
CS12800R101P-C111
CS12800R101E-C111 |
|
CS | Chipsee Product Abbreviate |
12 | Horizontal Resolution
80Means 800 Pixel 10Means 1024 Pixel 12Means 1280 Pixel 14Means 1440 Pixel 19Means 1920 Pixel |
800 | Vertical Resolution
480Means 480 Pixel 600Means 600 Pixel 768Means 768 Pixel 800Means 800 Pixel 900Means 900 Pixel 102Means 1024 Pixel 108Means 1080 Pixel |
R(F/T) | Product based on Rockchip (Freescale/TI) CPU |
101 | LCD Dimension
050Means 5.0 Inch 070Means 7.0 Inch 080Means 8.0 Inch 097Means 9.7 Inch 101Means 10.1 Inch 104Means 10.4 Inch 120Means 12.0 Inch 150Means 15.0 Inch 170Means 17.0 Inch 190Means 19.0 Inch 215Means 21.5 Inch |
P | Means Embedded PC or Panel PC
E Means Embedded PC without Case P Means Panel PC with Case |
C | Means Touch Type
R Means Resistive Touch C Means Capacitive Touch |
1 | Means LCD Brightness
1 Means Common Brightness 2 Means High Brightness |
1 | PCB Version
Baseboard PCB Version Number |
1 | PCB Version
SOM Module PCB Version Number |
Hardware Features
Key Features: | |
CPU | Rokchip RK3399, Dual-core Cortex-A72(1.8GHz), Quad-core Cortex-A53(1.4GHz) |
RAM | 4GB DDR3 |
eMMC | 16GB |
Storage | TF card, supports up to 32GB SDHC |
Display | 10.1 Inch LCD,1280*800Pixel Resolution |
Touch | Ten-Point Capacitive Touch |
USB | 2 x USB 2.0 Host, 1x USB 3.0 Host,1x Type-C |
LAN | 1 Channel 1000M LAN |
Audio | 3.5mm Audio In/Out Connector,2W Speaker Internal |
Buzzer | 1 |
RTC | Yes |
RS232+RS485 | Default 5xRS232 and 2x RS485 (Optional 4 x RS485 at most, 1 debug port) |
GPIO | 8 Channels |
WiFi/BT | On Board WIFI/BT |
HDMI | 1 Channel |
3G/4G | Optional |
Power Input | 15~36V DC |
Current @ 15V | 500 mA max |
Power Consumption | 7.5W Typical |
Working Temperature | -20°C to +70°C |
OS | Android 7.1, Linux, Debian 9.0 |
Dimension | CS12800R101P : 280*185.5*27.5mm
CS12800R101E : 245*155*11mm |
Weight | CS12800R101P : 1500g
CS12800R101E : 600g |
CS12800R101E-C111

Figure 1 Front View

Figure 2 Back View
CS12800R101P-C111

Figure 3 Front View

Figure 4 Back View
Power Input Connector
The product uses a wide range power input: DC 15~36V. The total power consumption is normally about 15W. The power input connector is a 3 pin 3.81mm screw terminal connector, as shown in Figure 3.
Table 1 describes how to connect the power supply.


Figure 3 Power Input Connector
Table 1
Power Input Pin Definition: | ||
Pin Number | Definition | Description |
Pin 1 | Positive Input | Connect to DC Power Positive Terminal |
Pin 2 | Negative Input | Connect to DC Power Negative Terminal |
Pin 3 | Ground | Connect to Power System Ground |
ATTENTION:
The system Ground has been connected to Negative Input on the board.
Capacitive Touch
The product CS12800R101P/ CS12800R101E uses a ten-point capacitive touch screen.
ATTENTION:
Capacitive touch screens are very sensitive to power noise. Ripple voltage/current from the power adapter can cause the LCD ripples, as well as the malfunction of the capacitive touch. If you use the APK Multi-Touch under Android to test it, you can find the touchpoint float. You can solve this problem by using:
- a high-quality power adapter.
- a battery to provide the power, like a cell phone or tablet PC
If the power adapter isn’t good enough, make sure Pin 3 is connected to the Ground. This can eliminate the problem totally. You can test it by touching the Ground of the product with one hand, and the capacitive touch screen with the other hand.
RS485+RS232 Connector
The RS485+RS232 connector is a 16 Pin 3.81mm Screw Terminal Connector, as Figure 6 shows. As for the definition of every pin, please refer to Table 2.This product has 7 channels of UART in total, they can be configured as RS232 or RS485 freely. If you need any other setting different to the default setting, please contact us.


Figure 6 RS485+RS232 Connector
Table 2
RS232 / RS485 / CAN Pin Definition: | ||
Pin Number | Definition | Description |
Pin 1 | RS485_4+ | USB UART4, RS485 +(A) signal |
Pin 2 | RS485_4- | USB UART4, RS485 -(B) signal |
Pin 3 | RS485_3+ | USB UART3, RS485 +(A) signal |
Pin 4 | RS485_3- | USB UART3, RS485 -(B) signal |
Pin 5 | RS232_2_RXD | USB UART2, RS232 RXD signal |
Pin 6 | RS232_2_TXD | USB UART2, RS232 TXD signal |
Pin 7 | RS232_1_RXD | USB UART1, RS232 RXD signal |
Pin 8 | RS232_1_TXD | USB UART1, RS232 TXD signal |
Pin 9 | CPU_RS232_4_RXD | CPU UART4, CPU RS232 RXD signal |
Pin 10 | CPU_RS232_4_TXD | CPU UART4, CPU RS232 TXD signal |
Pin 11 | CPU_RS232_0_RXD | CPU UART0, CPU RS232 RXD signal |
Pin 12 | CPU_RS232_0_TXD | CPU UART0, CPU RS232 TXD signal |
Pin 13 | CPU_RS232_2_RXD | CPU UART2, CPU RS232 RXD signal |
Pin 14 | CPU_RS232_2_TXD | CPU UART2, CPU RS232 TXD signal |
Pin 15 | GND | System Ground |
Pin 16 | +5V | System +5V Power Output, No more than 1A Current output. |
USB 2.0 Connector
There are four USB 2.0 connectors, as Figure 5 shows. Each can provide 500mA of current.


Figure 7 USB HOST Connector
USB 3.0 Connector
The product CS12800R101P/ CS12800R101E has one USB 3.0 connector as Figure 8 shows.


Figure 8 USB 3.0 Connector
USB Type-C
As well as one USB Type-C connector, as shown in Figure 9.


Figure 9 USB Type-C Connector
LAN Connector
The product CS12800R101P/ CS12800R101E has one channel 1000Mbit Ethernet Connector, as Figure 10 shows.


Figure 10 LAN Connector
TF Card
The product CS12800R101P/ CS12800R101E has one TF (uSD) card connector as Figure 11 shows. This device supports a TF (uSD) card up to 32GB.


Figure 11 TF Card Connector
ATTENTION:
A TF card does not come with the product.
SIM Card Holder
There is one SIM card holder, as shown in Figure 12. To read the SIM card data, you need a 3G/4G module. The product has a mini-PCIe connector inside that enables a 3G/4G module to be mounted.

Figure 11mini-PCIe Connector&4G Module



Figure 12 SIM Card Holder and 4G Antenna
ATTENTION:
The 4G module is not provided by default, but can be ordered along with the product. Please note that the Ubuntu driver for the 4G module is not available right now.
Audio Connector
The product CS12800R101P/ CS12800R101E has one Audio Input (“Line-in”) and one Audio (“Line-out”) output, as Figure 13 shows. It also has an internal 2W speaker.


Figure 13 Audio Connector
WiFi+BT
The product has one WiFi+BT module, based on the Realtech RTL8723, which integrates WiFi and BT. There is a connector on the backside case which can connect external WiFi and BT antenna, as shown in Figure 14.


Figure 14 WiFi+BT Antenna
HDMI Connector
The product CS12800R101P/ CS12800R101E has one HDMI connector as Figure 15 shows. The HDMI output resolution can be configured by software.


Figure 15 HDMI Connector
Power Button
Figure 16 shows the product’s power button.


Figure 16 Power On Button
Expansion Connector
The product CS12800R101P/ CS12800R101E has one Expansion Connector (closed by default), as Figure 17 shows. As for the definition of every Pin, please refer to Table 3.


Figure 17 GPIO Connector
Table 3
GPIO Connector Definition | |
Pin Number | Definition |
Pin 1 | IN4 |
Pin 2 | IN3 |
Pin 3 | IN2 |
Pin 4 | IN1 |
Pin 5 | OUT4 |
Pin 6 | OUT3 |
Pin 7 | OUT2 |
Pin 8 | OUT1 |
Pin 9 | GND_ISO |
Pin 10 | VCC_ISO |
ATTENTION:
This GPIO Connector is optional. If you need it, please contact us. All GPIO signals are isolated, and the VCC_ISO supports a 5V~24V input.
Measurements and Mounting
Measurements of CS12800R101P-C111
The measurement of CS12800R101P-C111 is 280*185.5*27.5mm

Measurements of CS12800R101E-C111
The measurement of CS12800R101E-C111 is 245*155*11mm

Mounting Method
The CS12800R101P can be mounted by screw holes (Vesa mount), by Panel mounting. The CS12800R101E can be mounted by Embedded mounting. Please make sure the display is not exposed to high pressure when mounting into an enclosure.
Installation Steps:
- Put the panel mount product in the cut out from the front side of the customer’s fixture, with the sides of the front bezel shown on the outside.
- Use the provided mounting kits to attach and tighten the panel mount product to the customer’s fixture as shown in the images.



Figure 18 Mounting Method
Mounting Method 2 – Embedded mounting
Installation Steps:
- Put the embedded mount product in the cut out from the front or rear side of the customer’s fixture.
- Fasten it with a screw from the front side.




Figure 19 Mounting Method
How to Get Support
Please feel free to contact us with any questions, queries or suggestions.
If your question is about technical support or troubleshooting for one of our products, we kindly ask you to first check our documentation for a possible solution.
If you cannot find the solution you are looking for then please write to service@chipsee.cn providing all possible details.

Chipsee assumes no responsibility for any errors, which may appear in this manual. Furthermore, Chipsee reserves the right to alter the hardware, software, and/or specifications detailed herein at any time without notice, and does not make any commitment to update the information contained herein. Chipsee products are not authorized for use as critical components in life support devices or systems.