User Manual
Release 1.0


Chipsee Products Naming Rules
CS12800F101E-C141 CS12800F101P-C141 |
|
CS | Chipsee Product Abbreviations |
12 | Horizontal Resolution
80 Means 800 Pixel 10 Means 1024 Pixel 12 Means 1280 Pixel 14 Means 1440 Pixel 19 Means 1920 Pixel |
800 | Vertical Resolution
480 Means 480 Pixel 600 Means 600 Pixel 768 Means 768 Pixel 800 Means 800 Pixel 900 Means 900 Pixel 102 Means 1024 Pixel 108 Means 1080 Pixel |
F(T) | Product based on Freescale (TI) CPU |
101 | LCD Dimension
050 Means 5.0 Inch 070 Means 7.0 Inch 080 Means 8.0 Inch 097 Means 9.7 Inch 101 Means 10.1 Inch 104 Means 10.4 Inch 120 Means 12.0 Inch 150 Means 15.0 Inch 170 Means 17.0 Inch 190 Means 19.0 Inch 215 Means 21.5 Inch |
P | Means Embedded PC or Panel PC
E Means Embedded PC without Case P Means Panel PC with Case |
C | Means Touch Type
R Means Resistive Touch C Means Capacitive Touch |
1 | Means LCD Brightness
1 Means Common Brightness 2 Means High Brightness |
4 | PCB Version
Baseboard PCB Version Number |
1 | PCB Version
SOM Module PCB Version Number |
Hardware Features
Key Features: | |
CPU | iMX6Q, Quad-A9,1GHz |
RAM | 2GB DDR3 |
eMMC | 8GB |
Storage | TF card, supports up to 32GB SDHC |
Display | 10.1 inch IPS LCD, 1280*800 Pixel Resolution, 16:9 Brightness: 250nit |
Touch | Ten-Point Capacitive Touch |
USB | 2 x USB 2.0 Host, 1 x USB OTG |
LAN | 1 x 1000M LAN, supports POE 1 x 100M LAN optional |
Audio | 3.5mm Audio In/Out Connector, 2W Speaker Internal |
Buzzer | 1 |
RTC | Yes |
RS232 | 2 Channels |
RS485 | 3 Channels * |
CAN | 2 Channels |
GPIO | 8 Channels |
WiFi/BT | On-Board WIFI/BT |
HDMI | 1 Channel |
SATA II | 1 Channel |
3G/4G | Optional, not mounted by default. |
Power Input | 12~36V DC |
Current @ 15V | 600 mA max (without 4G module) |
Power Consumption | 7W Typical |
Working Temperature | -20°C to +70°C |
OS | Android, Ubuntu, Linux |
Dimension | CS12800F101E: 245 x 155 x 11 mm CS12800F101P: 280 x 185.5 x 27.5 mm |
Weight | CS12800F101E: 600g CS12800F101P: 1410g |
* This product has 5 channels of UART in total. One UART channel is used for the Bluetooth by default, so the default setting is 2*RS232+2*RS485+Bluetooth. The UART can be changed between RS232 and RS485 easily. If you want different RS232 and RS485 setting, please contact us.
CS12800F101E-C141

Figure 1: Front View (Android)

Figure 2: Back View
CS12800F101P-C141

Figure 3: Front View

Figure 4: Back View
Power Input Connector
The product CS12800F101E/CS12800F101P uses a wide-range power input DC 12~36V. The total power consumption is normally about 7W. The Power Input Connector is a 3 Pin 3.81mm Screw Terminal Connector, as Figure 5 shows. A detailed description of the power input connector pins is provided in Table 1.


Figure 5: Power Input Connector
Table 1
Power Input Pin Definition: | ||
Pin Number | Definition | Description |
Pin 1 | Positive Input | Connect to DC Power Positive Terminal |
Pin 2 | Negative Input | Connect to DC Power Negative Terminal |
Pin 3 | Ground | Connect to Power System Ground |
ATTENTION:
The system ground “GND” has been connected to power negative “-” on board.
Capacitive Touch
The product CS12800F101E/CS12800F101P uses ten-point capacitive touch.
ATTENTION:
Capacitive touch is very sensitive to power noise. Ripple voltage/current from the power adapter will cause the LCD ripples, and will also cause the capacitive touch malfunction. If you use the APK Multi-Touch under Android to test, you can find the touchpoint float. There are several ways to solve this problem:
1) Use a high-quality power adapter. Or a battery to provide power like a cell phone or tablet PC.
2) If the power adapter isn’t good enough, make sure the CS10600U070E/CS10600U070P power input connector Pin 3 is connected to the Ground. This method can eliminate the problem totally. You can test it by touching the GND of CS10600U070E/CS10600U070P with one hand, while the other hand operates on the capacitive touch screen. In this case, the user’s body acts as the Power System Ground.
CAN+RS485+RS232 Connector
The CAN+RS485+RS232 connector is a 16 Pin 3.81mm Screw Terminal Connector, as Figure 6 shows. As for the definition of every pin, please refer to Table 2. This product has 5 channels of UART in total that can be freely configured as RS232 or RS485. If you need any other setting different from the default one, please contact us.


Figure 6: CAN+RS485+RS232 Connector
Table 2
RS232 / RS485 / CAN Pin Definition: | ||
Pin Number | Definition | Description |
Pin 1 | CAN2_L | CPU CAN Channel 2 L signal |
Pin 2 | CAN2_H | CPU CAN Channel 2 H signal |
Pin 3 | CAN1_L | CPU CAN Channel 1 L signal |
Pin 4 | CAN1_H | CPU CAN Channel 1 H signal |
Pin 5 | RS485_2+ | CPU UART2, RS485 +(B) signal |
Pin 6 | RS485_2- | CPU UART2, RS485 -(A) signal |
Pin 7 | RS485_5+ | CPU UART5, RS485 +(B) signal |
Pin 8 | RS485_5- | CPU UART5, RS485 -(A) signal |
Pin 9 | RS485_4+ | CPU UART4, RS485 +(B) signal |
Pin 10 | RS485_4- | CPU UART4, RS485 -(A) signal |
Pin 11 | RS232_3_RXD | CPU UART3, RS232 RXD signal |
Pin 12 | RS232_3_TXD | CPU UART3, RS232 TXD signal |
Pin 13 | RS232_1_RXD | CPU UART1, RS232 RXD signal |
Pin 14 | RS232_1_TXD | CPU UART1, RS232 TXD signal |
Pin 15 | GND | System Ground |
Pin 16 | +5V | System +5V Power Output, No more than 1A Current output. |
ATTENTION:
- UART2 signal has been used by Bluetooth signal onboard. The RS485_2 function has been disabled by default. If you need the RS485_2 function, please contact us to disable the Bluetooth function.
- A 120Ohm resistor doesn’t come mounted by default with the product.
USB HOST Connector
There are two USB connectors, as shown in Figure 7, that can provide 500mA current each.


Figure 7: USB HOST Connector
USB OTG Connector
And one USB OTG connector as Figure 8 shows. It works as a slave by default and can be used to connect the host PC.


Figure 8: USB OTG Connector
LAN Connector
The product has one channel 1000Mbit Ethernet Connector(LAN1), as Figure 9 shows. And this port support POE (Power-On-Ethernet). The other channel 100Mbit Ethernet Connector is optional.


Figure 9: LAN Connector
TF Card
The product CS12800F101E/CS12800F101P has one TF(uSD) card connector as Figure 10 shows. This device supports TF(uSD) card up to 32GB.


Figure 10: TF Card Connector
ATTENTION:
The TF card doesn’t come with the product by default.
SIM Card Holder
The SIM card holder is shown in Figure 11. To read the SIM card data, you need a 3G/4G module. There is a mini-PCIe connector inside the CS12800F101E/CS12800F101P that enables a 3G/4G module to be mounted. To connect the external 4G Antenna, shown in Figure 12, use a connector on the backside of the case.


Figure 11: SIM Card Holder


Figure 12: 4G Antenna
ATTENTION:
4G module is optional, it doesn’t come with the product by default. Only the Android 4.3 driver for 4G module is available at present.
Audio Connector
There is one Audio Input (“Line-in”) and one Audio (“Line-out”) output, as Figure 13 shows, as well as an internal 2W speaker.


Figure 13: Audio Connector
WiFi+BT
The product CS12800F101E/CS12800F101P has one WiFi+BT. It uses Realtech RTL8723 which integrates WiFi and BT. For CS12800F101P, there is a connector on the backside of the case that is used to connect an external WiFi/BT antenna, as Figure 14 shows.


Figure 14: WiFi+BT Antenna
HDMI Connector
The product CS12800F101E/CS12800F101P has one HDMI connector as Figure 15 shows. The HDMI output resolution can be configured by software.


Figure 15: HDMI Connector
Boot Switch
The product CS12800F101P has a boot switch that can be used to change the boot sequence, as Figure 16 shows. It is marked as SW2 on the PCB. As for the details on the boot switch functions, please refer to Table 3.

Figure 16: Boot Switch
Table 3
Boot Config Select: | ||||
Mode | 1 | 2 | 3 | 4 |
TF Card | 1 | 0 | 0 | 0 |
eMMC | 1 | 1 | 0 | 1 |
Download | 0 | 1 | 1 | 0 |
GPIO Connector
There is one GPIO Connector, as Figure 15 shows, marked as P28 on the PCB. As for the definition of every Pin, please refer to Table 4.


Figure 17: GPIO Connector
Table 4
GPIO Connector Definition | |
Pin Number | Definition |
Pin 1 | VCC, Isolated Power +5-24V Input |
Pin 2 | GND |
Pin 3 | OUT1 |
Pin 4 | OUT2 |
Pin 5 | OUT3 |
Pin 6 | OUT4 |
Pin 7 | IN1 |
Pin 8 | IN2 |
Pin 9 | IN3 |
Pin 10 | IN4 |
ATTENTION:
All these signals are connected to the CPU directly. Please use it carefully, otherwise, the CPU can be easily damaged.
Camera
The product CS12800F101E/CS12800F101P supports one channel CMOS camera. You should open the product’s backside of the case to find the camera connector, shown in Figure 18. It is marked as P26 on the PCB and supports camera OV2659, OV5640.

Figure 18: Camera Connector
Dimensions and Mounting
CS12800F101E
The dimensions of CS12800F101E are 245*155*11 mm, as Figure 19 shows.

Figure 19: Dimensions
The product CS12800F101E can be mounted using the 4 screw holes on the PCB as shown in Figure 20. Please make sure the display is not exposed to high pressure when mounting into an enclosure.

Figure 20: Mounting Method
CS12800F101P
The dimensions of CS12800F101P are 280*185.5*27.5 mm, as Figure 21 shows.

Figure 21: Dimensions
This product CS12800F101P can be mounted using the panel mounting method, as Figure 22 shows. Please make sure the display is not exposed to high pressure when mounting into an enclosure.



Figure 22: Mounting Method
How to Get Support
Please feel free to contact us with any questions, queries or suggestions.
If your question is about technical support or troubleshooting for one of our products, we kindly ask you to first check our documentation for a possible solution.
If you cannot find the solution you are looking for then please write to contact@chipsee.com providing all possible details.